ILCA / Laser
Active filters
Filter By
Brand
Brand
Active filters
Rooster's Polilite rope, ideal for mainsheet applications on racing dinghies.
Lightweight and high strength, single braid bio-based Dyneema SK78, with tough ArmourCoat finish
If you are looking for a glove suited to mainsheet trimming; where releasing the sheet is just as important as pulling in, the Dura Pro may be the answer. With double layer top quality abrasion resistant Amara on all high load/stress areas, these gloves are extremely supple with excellent grip and are perfect for all helming duties.
Low stretch and zero creep maintains sail set even when fully loaded over extended periods
The bio-based SK78 core is high strength and has minimal creep.
Ideal for Laser/ILCA outhaul, downhaul and vang systems.
The Technora blended cover gives the same fantastic abrasion and heat resistance properties as EXCEL ELITE. Technora blend cover adds grip for wet hands, and is easy to taper, showing colour matched ARMOURCOAT core.
Ideal for halyards, sheets and high strength control lines.
Neoprene sleeve bottle holder with adjustable webbing straps at each end to fit around different circumferences of tube.
Rooster toestraps use a unique rubber compound that has a very high coefficient of friction, whilst also being light and durable.
Rooster's Polilite rope, ideal for Laser/ILCA. 14 meters in length.
Low stretch, 100% Polyester rope offers great performance at a lower cost.
Marlow's High strength, lightweight with 100% Polyester cover and Dyneema® core for all round use on halyards, sheets and control lines.
These bailer spring plates are manufactured using the highest quality spring stainless steel, designed to both retract using spring tension, and at the same time providing a surface for the activator to push against to close the chute.
Rooster's 50mm clew strap suitable for Laser/ILCA.
Laser Mast Wear Kit contains two stripes of UHMWPE with acrylic adhesive on liner to be applied on the mast boot and mast collar complete to reduce the wear and tear of the gelcoat.
Two stripes of 21 mm of width and 200 mm in length.
Official batten set for ILCA 4 and ILCA 6. Also suitable for Laser 4.7 and Laser Radial.
Official carbon lower mast section for ILCA 6
Holt replica sail for Laser Radial or ILCA 6. Batten set no included

Official batten set for ILCA 7. Also suitable for Laser Standard
RWO Omniflex Joint with rope core in case the rubber joint fails. Suitable for extensions with an internal tube diameter of 13mm, hole centers 32mm.
Rooster's Polilite rope, ideal for Laser/ILCA. 14 meters in length, 7 mm diameter
Holt's hiking strap for Laser/ILCA. Length of 870 mm.
Holt replica aluminum top mast for Laser/ILCA.

A pack of three green and three red self adhesive wool telltales (with TEFLON treatment) that don´t stick to the sail in the wet.
Holt Grab Rail suitable for all Laser Performance and ILCA Dinghies
Laser 4.7/ILCA 4 Replica Lower Mast produced by Holt.

Laser Radial/ILCA 6 Replica Lower Mast produced by Holt.

Rooster Sailing self adhesive grip tape for use on your deck.
Moulds to fit the surface applied to providing a strong connection and durable grip. When you want to remove it, it's easy and clean and does not leave any residue when peeled off.
Available in a number of colours.
Holt replica sail for Laser Standard or ILCA 7, horizontal cut. Batten set no included, folded.

Holt Mk2 replica sail for Laser Standard or ILCA 7. Batten set no included, delivered folded.

16 mmHPN rope stopper ball.
Maximum rope diameter: 5 mm.
Available in blue, red, green, black and white