ILCA / Laser
Active filters
Filter By
Brand
Brand
Active filters
Rooster's Polilite rope, ideal for mainsheet applications on racing dinghies.
Allen Brothers' Dynamic 20mm Single Tie-On block. Suitable for the downhaul and outhaul systems of Laser/ILCA.
If you are looking for a glove suited to mainsheet trimming; where releasing the sheet is just as important as pulling in, the Dura Pro may be the answer. With double layer top quality abrasion resistant Amara on all high load/stress areas, these gloves are extremely supple with excellent grip and are perfect for all helming duties.
Neoprene sleeve bottle holder with adjustable webbing straps at each end to fit around different circumferences of tube.
Rooster toestraps use a unique rubber compound that has a very high coefficient of friction, whilst also being light and durable.
Rooster's Polilite rope, ideal for Laser/ILCA. 14 meters in length.
These bailer spring plates are manufactured using the highest quality spring stainless steel, designed to both retract using spring tension, and at the same time providing a surface for the activator to push against to close the chute.
Rooster's 50mm clew strap suitable for Laser/ILCA.
Laser Mast Wear Kit contains two stripes of UHMWPE with acrylic adhesive on liner to be applied on the mast boot and mast collar complete to reduce the wear and tear of the gelcoat.
Two stripes of 21 mm of width and 200 mm in length.
Official batten set for ILCA 4 and ILCA 6. Also suitable for Laser 4.7 and Laser Radial.
Official carbon lower mast section for ILCA 6
Ready to sail Holt replica Laser/ILCA boom, fitted with ball bearing blocks.
Holt replica sail for Laser Radial or ILCA 6. Batten set no included
Official batten set for ILCA 7. Also suitable for Laser Standard
Rooster's Polilite rope, ideal for Laser/ILCA. 14 meters in length, 7 mm diameter
Holt's hiking strap for Laser/ILCA. Length of 870 mm.
Holt's cleats and base plate assembly for Laser/ILCA. Ready to be installed.
Holt replica aluminum top mast for Laser/ILCA.
A pack of three green and three red self adhesive wool telltales (with TEFLON treatment) that don´t stick to the sail in the wet.
Holt Grab Rail suitable for all Laser Performance and ILCA Dinghies
Laser 4.7/ILCA 4 Replica Lower Mast produced by Holt.
Laser Radial/ILCA 6 Replica Lower Mast produced by Holt.
Rooster Sailing self adhesive grip tape for use on your deck.
Moulds to fit the surface applied to providing a strong connection and durable grip. When you want to remove it, it's easy and clean and does not leave any residue when peeled off.
Available in a number of colours.
Holt replica sail for Laser Standard or ILCA 7, horizontal cut. Batten set no included, folded.
Holt Mk2 replica sail for Laser Standard or ILCA 7. Batten set no included, delivered folded.
Allen Brothers Laser / ILCA Lower Vang Unit.
This Laser vang unit offers ultimate control over your vang control line. The cam cleat is mounted to a swivel, this ensures you can pull the vang control line from any angle and with minimal friction.
The block formation of our Laser / ILCA vang unit ensures the vang control line does not twist under load.
Easily attached to the Laser / ILCA mast tang with a nut and bolt.
Also featured is a removable clevis pin which can be used to dead-end the Cunningham control line.
This product is ILCA and Laser class legal.
Laser/ ILCA control line cam cleats with angled base, Pro-lead and wire under-fairleads.
The base has been optimised with a small angle to ensure the control lines can easily be adjusted when hiking and the Pro-lead ensures the rope guides easily into the mouth of the cam cleat from any angle.
This product is ILCA and Laser class legal.
16 mmHPN rope stopper ball.
Maximum rope diameter: 5 mm.
Available in blue, red, green, black and white